Plumbing Basics: What You Need for Installing a Bathtub
Plumbing Basics: What You Need for Installing a Bathtub
Blog Article
Were you in search of selective information about Tools You Need to Install a New Bathtub ?
Setting up a tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably tough job. If the old tub is conveniently available, the project can relocate immediately; if you have to open up a wall to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have actually certified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed task, it is far better to take into consideration using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This post will certainly assist you set up a new bath tub in your restroom if you have actually already gotten a new tub and also do not need to change the plan of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite problematic because of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric ready for the staying water that will come from the pipes. As soon as the supply pipes have been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and also the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former type should be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the needed position. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its last setting.
Getting ready for the Setup
First of all, the supporting structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a rigid seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, causing complications with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealant can crack rather very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our piece about How to Install a Bathtub. Thanks so much for finding the time to browse our short article. Enjoyed our blog posting? Please share it. Let someone else locate it. Thanks a lot for taking the time to read it.
Tap problems? Reach. Report this page